<p>The Cantek Drawer Notcher JEN-60 is designed to both notch and drill drawer boxes to install undermount soft-close drawer slides. The operation of the machine is simple with a self-indexing drilling unit that’s determined by the position of the drawer for either left or right notching. With a cycle time of approximately 10 seconds per drawer, you can achieve a high throughput.</p>
<p><span style="font-size: 1.231em; font-weight: bold;">Features:</span></p>
<div>
<ul>
<li>Pneumatic cutter & drill stroke by foot pedal operation.</li>
<li>Cutter stroke and drill speed are adjustable for optimum finish results.</li>
<li>Drill will automatically position for both left and right drawer notches by activating a switch in the fence.</li>
<li>Machine will not cycle unless a drawer is up against the switch for safe operation.</li>
<li>Insert knife cutterhead with solid carbide inserts for optimum finish results and long tool life.</li>
<li>2 ¼” (57mm) wide cutter allows for a wide range of undermount slides.</li>
<li>Comes with insert cutterhead with inserts and ¼” (6.3 mm) solid carbide drill bit.</li>
<li>Capable of notching up to 220 drawer boxes (both left and right) per hour.</li>
</ul>
<p> </p>
<table style="width: 348px; height: 603px;">
<tbody>
<tr>
<td width="149">
<p><strong>Specifications:</strong></p>
</td>
<td width="159"> </td>
</tr>
<tr>
<td width="149">
<p>Main Cutter Motor</p>
</td>
<td style="text-align: center;" width="159">
<p>3 HP</p>
</td>
</tr>
<tr>
<td width="149">
<p>Notch Dimensions</p>
</td>
<td style="text-align: center;" width="159">
<p>2 ¼” (57mm) x 0.5” high</p>
</td>
</tr>
<tr>
<td width="149">
<p>Cutter Diameter</p>
</td>
<td style="text-align: center;" width="159">
<p>10”</p>
</td>
</tr>
<tr>
<td width="149">
<p>Drill Diameter</p>
</td>
<td style="text-align: center;" width="159">
<p>¼”</p>
</td>
</tr>
<tr>
<td width="149">
<p>Table Size</p>
</td>
<td style="text-align: center;" width="159">
<p>49” x 22”</p>
</td>
</tr>
<tr>
<td width="149">
<p>Table Height from Floor</p>
</td>
<td style="text-align: center;" width="159">
<p>32”</p>
</td>
</tr>
<tr>
<td width="149">
<p>Dust Port</p>
</td>
<td style="text-align: center;" width="159">
<p>4” (670 CFM requirement)</p>
</td>
</tr>
<tr>
<td width="149">
<p>Compressed Air Required</p>
</td>
<td style="text-align: center;" width="159">
<p>90 – 100 PSI</p>
</td>
</tr>
<tr>
<td width="149">
<p>Machine Dimensions</p>
</td>
<td style="text-align: center;" width="159">
<p>48” x 37 ¾” x 39 ¾”</p>
</td>
</tr>
<tr>
<td width="149">
<p>Machine Weight</p>
</td>
<td style="text-align: center;" width="159">
<p>506 lbs.</p>
</td>
</tr>
</tbody>
</table>
</div>